1968 Ford Mustang Convertible Project with tons of extras
1968 Ford Mustang Convertible Description:
1968 Mustang Convertible Project w/ tons of parts !!
I am unloading a mustang project that I have had in my garage for about ten years.I have lost all interest in building this project.Over the years I accumulated a large amount of parts and sheet metal for this project.So much so that it would be extremely difficult for me to list each piece individually, so I am providing pictures and a high-level check list below.
Please note that the Mustang does not have an engine, or transmission, or exhaust system, or drive shaft, or radiator. (As can be seen in the pics). There is some pitting on the chrome as well as door gaps that will need to be adjusted. Paint in fair condition, not great.
I have already completed the following:
·seats reupholstered
·top reupholstered
·the dash/instrument panel redone
·replaced wiring with a painless wiring harness
·Installed a complete Vintage Air A/C kit
Here is a listing of accumulated parts and supplies. All parts are new and uninstalled. Note, that the Mustang does not need the sheet metal installed, my opinion.The sheet metal can be used for other projects you may have.
| Item # | Description |
| Full Floor Pan | |
| Seat Platform | |
| Seat Base | |
| Seat Base | |
| Inner Support Frame | |
| inner Support Frame | |
| Rear Torque Box with Rear Frame Rail | |
| Rear Torque Box with Rear Frame Rail | |
| Reinforcement Plate | |
| Firewall Extension | |
| Firewall Extension | |
| Outer Torque Box | |
| Outer Torque Box | |
| Upper Rear Torque Box Patch | |
| Upper Rear Torque Box Patch | |
| Front Torque Box | |
| Front Torque Box | |
| Front Floor Support | |
| Floor Pan under Rear Seat | |
| Floor Pan under Rear Seat | |
| Reinforcement Floor Pan | |
| Reinforcement Floor Pan | |
| Rear Apron Extension | |
| Rear Apron Extension | |
| LH Rear Fender Apron | |
| LH Fender Apron | |
| RH Front Fender Apron | |
| RH Rear Fender Apron | |
| Inner Rocker Paanel | |
| Inner Rocker Panel | |
| Door Panel | |
| Door Panel | |
| Quarter Trim Panel | |
| Quarter Trim Panel | |
| Pioneer Speaker Kick Panel | |
| Pioneer Speaker Kick Panel | |
| Kick Panel | |
| Kick Panel | |
| Jack Storage Bag | |
| Speckled Tire Cover | |
| Car Cover | |
| Windshield Piller Trim | |
| Windshield Piller Trim | |
| Hood Hinge | |
| Hood Hinge | |
| Hood Latch | |
| Hood Spring | |
| Hood Spring | |
| Hood | |
| Classic Auto Air Parts 1 | |
| Classic Auto Air Parts 2 | |
| Painless Wiring Kit | |
| Misc Parts - Air Filter, Hoses, etc: Used | |
| Box of Carbs (3): Used | |
| 3 Point Seat belt Kit | |
| Chrome Alternator / High Starter: Used | |
| Hardware 1 | |
| Hardware 2 | |
| Misc Parts 2 | |
| Gas Tank |
I am starting this auction at $5,000 with no reserve.If it ends there so be it.I have more pics below.
I am located in Poteau, Ok which is about 250 miles NE of Dallas, about 200 miles east of Oklahoma City, and about 150 miles South of Tulsa. Since there are a large amount of parts that will not fit in the vehicle you will probably need to come and get it yourself or hire someone who is able to carry all of the parts in addition to a non operational vehicle.
